Something stopped working and you are not sure why. A breaker tripped and will not stay on. An outlet went dead. The lights in one room flicker every time the refrigerator kicks on. These are the kinds of problems to describe when you reach us. We scope the job on the phone, explain what the work involves, and give you a price before anything is scheduled. We are open every day from 6:00 AM to 10:00 PM.
Union's housing stock is older on average, and the electrical systems in many of those homes reflect that. Knob-and-tube wiring, undersized panels, and circuits that were added over the years without documentation are all common. We handle residential and commercial electrical work throughout Union and the surrounding area. Whether the job is a straightforward repair or a full panel replacement, the process is the same: you call, we talk through it, and nothing moves forward until the scope and the price are clear.
What a job costs depends on what the job turns out to be. A tripping breaker might be a simple overload on a shared circuit, or it might be a failing breaker, a wiring fault, or a panel that has run out of capacity. The fault determines the fix, and the fix determines the price. We do not quote a number before we understand what we are dealing with.
Three things tend to move a quote in one direction or another. The first is what the fault actually is once it is traced. The second is whether reaching it requires opening a wall, pulling a fixture, or getting into the panel. The third is whether the existing circuit or panel can carry whatever change is being made, or whether additional work is needed to support it. A load calculation is part of that conversation when the job involves adding circuits or replacing a panel.
When you call, we work through those questions with you on the phone. You get a price before we schedule, and you know what it covers. If something unexpected turns up once we are on site, we tell you before the scope changes.
Houses of a certain age carry wiring that was installed to the standards of its time, and those standards have changed considerably. Knob-and-tube wiring is still present in some of the older properties in Union County. It is a fabric-insulated system run through ceramic knobs and tubes, and it was not designed for the loads a modern household draws. It is also not grounded, which matters for anything that requires a three-prong outlet.
Aluminum branch circuit wiring is another thing that turns up, particularly in homes that were built or rewired during a period when copper prices made aluminum a common substitute. Aluminum wiring is not automatically a problem, but the connections require specific devices and techniques to stay safe over time. Improperly terminated aluminum wiring is one of the more common causes of the kind of heat buildup that shows up as warm outlet covers or flickering lights under load.
Flickering lights and warm outlets are warning signs, not quirks. When either of those shows up, the right step is a diagnostic visit, not a wait-and-see. We identify what is present, explain what it means, and give you a clear picture of the work before anything is scheduled.
Planned work gets booked on the call. We scope the job, confirm the price, and settle on a time that works. For a panel upgrade, a rewire, or a dedicated circuit installation, a few days of lead time is usually enough to get the work on the calendar.
Some problems will not wait. A panel that is sparking, an outlet that is hot to the touch, or a circuit that has gone dead in a way that affects critical systems are all reasons to call without waiting. We take urgent calls every day from 6:00 AM to 10:00 PM. Describe what you are seeing on the phone and we will tell you what the situation calls for.
For rental properties and occupied businesses, we work around what is there. A tenant who cannot be without power for a full day is a scheduling constraint we account for before the work starts, not after. The same goes for commercial spaces that have to stay open. We confirm what the job requires and what the property requires, and we work the two together before anyone is dispatched.
We find work done by previous electricians on almost every property we visit, and most of it is fine. Wiring that meets current standards and is properly terminated does not need to be touched. A circuit that was added without a permit but was done correctly is a different situation from one that was done incorrectly. We look at what is actually there before we say anything about it.
What does need attention is work that creates a real risk: connections that were not made with the right devices, circuits that are overloaded and were never corrected, grounding and bonding that is absent or incomplete. GFCI and AFCI protection that was required at the time of installation but was never added falls into the same category. We explain what we find, what it involves to correct, and what the correction costs. The decision is yours.
When a permit was not pulled for work that required one, we can scope the correction and handle it. We do not make a production of it. The goal is to leave the property wired correctly. Most of the practical detail sits on our electrical repair services page.
A panel replacement is the right answer when the existing panel is undersized for the load, when breaker slots are exhausted, or when the panel itself is failing. Older panels in Union County homes sometimes carry breakers that no longer trip reliably, which is a safety issue regardless of the available capacity. We handle the load calculation, the panel replacement, and the service entrance work when the utility connection needs to be updated to match.
A full rewire comes up when the wiring throughout the home is knob-and-tube or otherwise past the point where repairs are a reliable fix. A partial rewire is the right scope when the problem is contained to a section of the house, an addition, or a specific circuit type. Either way, the scope is determined by what is actually present, not by a default recommendation.
A panel-level surge protector catches voltage spikes before they reach the outlets and devices throughout the house. Severe thunderstorms and the occasional ice storm across this region make that kind of protection practical rather than optional, particularly for homes with electronics, EV chargers, or standby generators connected to the system. It installs at the panel and covers every circuit at once.
Equipment that draws heavy current needs a dedicated circuit sized for the load it actually pulls. A welder, an air compressor, or a large woodworking tool running on a shared household circuit is how breakers trip and wiring overheats. We run the circuit, install the outlet or connection point, and confirm the panel has capacity before the work starts. Subpanel installation is sometimes the right answer when a detached workshop needs several circuits of its own.
Three-way switches control a single fixture from two locations, and they fail in ways that are not always obvious. A switch that works from one end but not the other, or a fixture that behaves inconsistently, usually points to a wiring problem at one of the switch locations rather than a fixture problem. We trace the circuit and correct it.
An inspection covers the panel, visible wiring, outlets, grounding, and bonding throughout the property. It is useful before a purchase, after a renovation, or when a property has not been evaluated in a long time. The report documents what is present and what, if anything, needs attention. Code corrections identified during an inspection can be scoped and scheduled at the same time.
Inside the home, the most common lighting requests involve replacing fixtures that have stopped working, adding recessed lighting in rooms that rely on a single overhead bulb, and installing dimmer switches where a standard switch was never adequate. Under-cabinet lighting in kitchens is a frequent addition when a remodel opens up the opportunity.
Outside, security lighting and motion sensor lights are worth doing at the same time as other exterior work, because the wiring run is already open. Porch lights, driveway lighting, and weatherproof outlets for patios and outbuildings are all part of the same category. We run the circuit, install the fixture, and test everything before we leave.
If a lighting project requires a new circuit rather than a connection to an existing one, that is part of the quote conversation. We confirm what the panel can support before the work is scoped.
We handle electrical work throughout Union and Union County, including Jonesville, Buffalo, Monarch Mill, Lockhart, and Carlisle. Properties in these communities are covered the same way: the job is scoped on the call, the price is confirmed before scheduling, and the work is handled without repeat visits to finish what was started.
Not the biggest name in town. Just the one that answers. No runaround.
Yes. We regularly handle electrical work on vacant properties. The job is scoped on the phone before anyone is dispatched, and access arrangements are confirmed at that point so the visit goes smoothly without a tenant present.
In many cases, yes. If the work involves circuits that do not feed the refrigerator or freezer, those appliances can stay on. When the panel itself needs to be de-energized, there will be a period without power to those circuits. We talk through which appliances will be affected when we scope the job, so you can plan accordingly.
Older properties in this area often carry wiring systems that were installed to standards that have since changed, including knob-and-tube wiring and aluminum branch circuit wiring that requires specific handling. The age of the home shapes what we look for on a diagnostic visit and what we recommend. We explain what is present and what it means before any work is scoped, so you understand what you are deciding.
A commercial office build-out typically involves adding circuits for workstations and equipment, installing outlets at the right locations for the layout, setting up lighting on appropriate circuits, and confirming the panel has capacity for the total load. We scope the electrical requirements based on the floor plan and the equipment list before any work is scheduled.
Sometimes, yes. If the panel has open breaker slots and the available capacity is adequate for the additional load, a new circuit can be added without replacing the panel. We check both of those things on the visit before any wiring is run, and if the panel cannot support the new circuit, we explain the options before the work proceeds.
Stop using the circuit and call us to describe what is happening. A breaker that will not hold is signaling a fault, an overload, or a panel problem, and resetting it repeatedly puts stress on the wiring without addressing the cause. We trace the problem to its source before any repair is quoted or started. We are available every day from 6:00 AM to 10:00 PM.
Someone should be available at the start of the visit so we can confirm access to the panel and the areas where work will happen. For longer jobs, you do not need to stay in the room the whole time, but we will check in with you before any scope changes and before we leave.
Describing what you are seeing is enough. A light that flickers, a breaker that will not stay on, an outlet that is warm, a room that went dark without warning.
Call (839) 293-6956, tell us what is happening, and we will work out what it involves and what it costs before anything is scheduled. We are available every day from 6:00 AM to 10:00 PM.
We take calls for Union and the surrounding area. Describe the problem and we will take it from there.
Other towns where we take electrical work: Chester, Gaffney, East Gaffney, Winnsboro.
When something goes wrong with the wiring or the panel, the right starting point is a clear picture of what the job involves and what it will cost. We scope every job on the phone before anyone is dispatched, explain the work in plain terms, and confirm the price before anything is scheduled. The table below covers the electrical services we handle in Union and Union County, along with who each one fits best and what is practical to know before you call.
| Type of Work | What's Included | Ideal For | Good to Know |
|---|---|---|---|
| Electrical Panel & Service Upgrades |
| Homeowners renovating, adding appliances, or running out of breaker slots | Union's rapid growth means many homes are being expanded beyond what their original panel was sized for. A load calculation is the first step. |
| Outlet & Switch Installation |
| Homeowners adding outlets or replacing outdated devices | Kitchens, bathrooms, garages, and outdoor areas have specific code requirements for GFCI protection. We confirm what applies before the install. |
| Backup Generator Installation |
| Homeowners who lose power during Union County storm season and need essential circuits to stay on | We handle the electrical side of the connection. The transfer switch is the critical piece that keeps the generator from back-feeding the utility line. |
Call (839) 293-6956 to talk through what you are dealing with and get a price before anything is scheduled. We are available every day from 6:00 AM to 10:00 PM.
(839) 293-6956